Automatic Gates Australia - Safety beam photocells.

Safety Devices - Photocells- Loops - Edge Strips
Safety devices used extensively in automatic gates come in a range of types with the main being safety beams, in ground loops and to a lesser extent edge strips. Once avoided due to the extra cabling work involved quite a few safety devices can no be used wirelessly.

	SAFETY BEAM BY KEY Photo electric safety beam suitable to 20 metres. Powered by 12 or 24 volts, ac or dc. BEAMKEY - $84.00

	SAFETY BEAM BY RIB Slim line photo electric safety beam suitable to 30 metres. Only 25mm wide Powered by 12 or 24 volts, ac or dc. BEAMRIB - $105.00

	SAFETY BEAM BY TAU Photo electric safety beam suitable to 20 metres. Powered by 12 or 24 volts, ac or dc. BEAMTAU - $86.00

	SAFETY BEAM WITH LITHIUM POWERED RECEIVER Photo electric safety beam suitable to 25 metres. Powered by 12 or 24 volts, ac or dc. If cabling is difficult one side of these beams can be powered by two lithium AA batteries with a life of approximately 15 months before battery change. Beams have low battery indicator. BEAMBATTRIB - $199.00 BATT3.6VAA - Batteries $15.00 EACH (Two Required)


	SAFETY BEAM WITH BATTERY POWERED RECEIVER Photo electric safety beam suitable to 20 metres. Powered by 12 or 24 volts, ac or dc. If cabling is difficult one side of these beams can be powered by a lithium battery pack with a life of approximately 15 months before battery change. Beams have low battery indicator. BEAMBATTKEY - $108.00 BATT1.5VAAA - $2.00 (NEED TWO)

	SAFETY BEAM STRIP TYPE The ESHEILD is a set of six beams in one strip at 1120mm long. Set up as a pair you effectively have six beams at approximately 200mm intervals. Use when you want to cover multiple heights. ESHEILD - $588.00


	SAFETY BEAM INDUSTRIAL REFLECTOR TYPE Reflective photo electric safety beam suitable to 11 metres. Powered by 12 or 24 volts, ac or dc. The beauty of this beam is that it only requires cabling and power to one side. Perfect for retro fit installations. BEAMPR11B - $551.00


	LOOP DETECTOR The MD2010 is a simple to install in ground loop detector. It has a full range of sensitivity settings and options. Vehicle detection loops are used to detect vehicles passing or arriving at a certain point, for instance approaching a gate, and in gate safety management. An insulated, electrically conducting loop is installed in the pavement. The electronics unit transmits energy into the wire loops at frequencies between 10 kHz to 200 kHz, depending on the model. The inductive-loop system behaves as a tuned electrical circuit in which the loop wire and lead-in cable are the inductive elements. When a vehicle passes over the loop or is stopped within the loop, the vehicle induces eddy currents in the wire loops, which decrease their inductance. The decreased inductance actuates the electronics unit output relay, which sends a pulse to the traffic signal controller signifying the passage or presence of a vehicle. MD2010 - $218.00


	LOOP DETECTOR PD134 Single Channel Detector This version includes variable delay timing to suit specific applications. The detector output is delayed until a vehicle has been present on the loop for the selected period. The programmable delay intervals are 0, 2, 4 or 6 seconds. 12/24 Volts AC/DC LOOPDETECTOR - $389.00


	FLASHING LIGHT 24 VOLT This flashing light is designed to connect direct to your gate system logic control and operates as a warning system whilst the gate is moving. FLASHER24 - $63.00

	FLASHING LIGHT 240 VOLT This flashing light is designed to connect direct to your gate system logic control and operates as a warning system whilst the gate is moving. FLASHER240 - $66.00

	WIFI SAFETY BEAMS WIFI safety beams allow complete installation of safety beams without any wires at all. The beams are powered by battery that under normal working conditions will last up to 15 months. WIFIBEAMS - $271.00 WIFIMASTER - $208.00 Note: You only need one WIFIMASTER with multiple WIFI devices. For example you can use two sets of WIFIBEAM and one WIFIEDGE but still only need one WIFIMASTER.


	WIFI SAFETY EDGE WIFI safety edge is a two metre long strip designed to on the closing face of a sliding or swing gate. When the rubber strip comes in contact with any object it compresses and send a signal to the WIFIMASTER that it has found an obstruction causing the gate to stop. WIFIEDGE - $381.00 WIFIMASTER - $208.00 Note: You only need one WIFIMASTER with multiple WIFI devices. For example you can use two sets of WIFIBEAM and one WIFIEDGE but still only need one WIFIMASTER.